lcd modules lcd modules lcd modules
lcd modules lcd modules lcd modules



Golden View Display Incorporated

   8460 Southwind Bay Circle
   Ft. Myers, FL 33908  USA
   Telephone:  239-332-8868
   Fax:   239-590-6066

sales@goldenviewdisplay.com

 

Golden View Display wants you to make an informed choice among our LCD products. The tech center provides you with most of the information you will need to understand liquid crystal displays.

Handling Precautions for LCD Products

A LCD is made up of glass, organic sealant, organic fluid and polymer based polarizers. The following precautions should be taken when handling:

  1. Keep the temperature within range for use and storage. Excessive
    temperature and humidity could cause polarization degradation, polarizer
    peel-off or bubble generation. When storage for a long period over 40°C
    is required, the relative humidity should be kept below 60%.
  2. Do not contact the exposed polarizers with anything harder than an HB
    pencil. To clean dust off the display surface, wipe gently with cotton,
    chamois or other soft material soaked in petroleum benzine. Never scrub
    hard.
  3. Wipe off saliva or water drops immediately. Contact with water over a
    long period of time may cause polarizer deformation or color fading, while
    an active LCD with water condensation on its surface will cause corrosion
    of ITO elctrodes.
  4. Petroleum Benzine is recommended to remove adhesives used to attach
    front/rear polarizer and reflectors, while chemicals like acetone, toluene,
    ethanol and isopropyl alcohol will cause damage to the polarizer. Avoid
    oil and fats. Avoid lacquer and epoxies which might contain solvents and
    hardeners to cause electrode erosion. Some solvents will also soften the
    epoxy covering the pins and thereby weaken the adhesion of the epoxy
    on glass. This will cause the exposed electrodes to erode electro-
    chemically when operating in high humidity and condensing environment.
  5. Glass can be easily chipped or cracked from rough handling, especially
    at corners and edges.
  6. Do not drive LCD with DC voltage. It will damage the LCD.
  7. When soldering DIL pins, avoid excessive heat and keep soldering
    temperature between 260°C and 300°C for no more than 5 seconds.

Operation

  • The viewing angle can be adjusted by varying the LCD driving voltage.
  • Driving voltage should be kept within specified range, excess voltage
    shortens display life.
  • Response time increases with decerase in temperature.
  • Display may turn black or dark blue at temperatures above its operating
    range, however, this is not destructive and the display will return to normal
    once the temperature falls back to range.
  • Mechanical disturbance during operation (such as pressing on the viewing
    area) may cause the segments to appear "fractured". They will recover
    once the display is turned off.
  • Condensation at terminals will cause malfunction and possible electro-
    chemical reaction. Relative humidity of the environment should therefore
    be kept below 60%.

Storage

  1. Store LCDs and modules in dark places and do not expose to sunlight or
    fluorescent light. Keep the temperature between 0°C to 35°C and the
    relative humidity low.
  2. Modules should be kept in antistatic packaging. If properly sealed, there
    is no need for desiccant.

Safety

  • If any fluid leaks out of a damaged glass cell, wash off with soap and
    water any human part that comes into contact with the fluid. Never
    swallow the fluid. The toxicity is extremely low but caution should be
    exercised at all times.

 

 
 
 
 
 
 
 
lcd modules
lcd modules  
lcd modules lcd modules Liquid Crystal Displays

Home  |  Our Factory  |  Contact  |  Standard LCD Glass  |  Module Numbering System  | Character LCD Module  | Graphic LCD Module  | Packaging Information  | LCD Controllers  | Intro to Liquid Crystal Displays  | Selecting a display type  | Driving your display  | Font Selection  | Troubleshooting  | Handling Precautions for LCD  | Handling Precautions for LCD Modules

Copyright © Golden View Display 2014
Design by swflwebmaster